Roten op het veld wordt ook wel ‘dauwroten’ genoemd.
Roten: ‘losweken’ van bastvezel en kernmateriaal in de plant
Na het oogsten blijft het hennepstro een aantal weken op het land liggen. Tijdens deze periode wordt door micro-organismen onder invloed van herhaaldelijk nat worden, o.a. door dauw, de lijmlaag tussen bastvezel en houtige kern in de plant verzwakt; dit heet ‘roten’. Gedurende het roten wordt de hennep enkele malen gekeerd om het rotingsproces homogeen en optimaal te laten verlopen. Door verzwakking van de lijmlaag (pectine) kunnen vezel en kernmateriaal (scheven) tijdens de volgende verwerkingsstap goed gescheiden worden (§6.1 voor technische toepassing en §7.1.1 voor textiel). De exacte duur van het roten is afhankelijk van het weer; de afbraak is een samenspel tussen regen, dauw en temperatuur.
Voor technische toepassingen is de rootduur ongeveer 2 weken en wordt 2 à 3 maal gekeerd. Voor textiel is de rootduur 5 à 6 weken en wordt 1 à 2 maal gekeerd.
Wanneer het rotingsproces te ver gaat, noemen we het rotten of overroten; de hennepvezels worden zwakker en verminderen in waarde. Zo resulteert overrote hennep in relatief meer korte zwingel- en hekel-‘afval’ vezel (§7Retting on the field is also known as 'dew-retting’.
Retting: 'loosening' of the bast fibre from the core material in the plant stalk
After harvesting, the hemp straw remains on the land for several weeks. During this period, microorganisms weaken the glue layer between the bast fibre and the woody core in the plant under the influence of water (rain and dew); this process is called 'retting'. During retting, the hemp is turned several times to make sure the retting process is homogeneous and optimal. By weakening the glue layer (pectin layer), the fibre and core material (shives) can eventually be separated during the further processing step (§6.1 for technical application and §7.1.1 for textiles). The exact duration of retting depends on the weather; decomposition depends on rain, dew, and temperature.
For technical applications, the retting lasts about 2 weeks and the stems are turned every 2 to 3 times. For textiles, the retting duration is up to 5 - 6 weeks and the stems are turned once or twice.
When the retting process proceeds beyond needs, the stems are over-retted: the hemp fibres become weaker and have a lower value. Over-retted hemp results in relatively large share of short fibres during scutching and hackling (§7.1.1, 7.1.3). Wanneer het stro te weinig geroot is, zal het scheiden van bastvezel en kernmateriaal meer energie kosten Conversely, when the straw is under-retted, separating the bast fibre from the core material will require more energy (§6.1), waardoor tevens de vezels meer beschadigd worden.
...
Bepalen van mate van roting
Tijdens het roten verkleuren de stengels van groen naar geel en tenslotte grijs (Foto beneden). De mate van roten kan bepaald worden met een betrekkelijk eenvoudige test (zogenaamde which also results in damages to the fibres.
...
Determining the retting degree
During retting, the stems turn from green to yellow and finally grey (see image below). The degree of retting can be determined with a relatively simple test (the so-called Fried test):[1]
Plaats een stuk hennepstengel van Place a piece of hemp stem of 8 cm lengte in een slank flesje/flacon.
Voeg kokend water tot zodat de gehele stengel onder water staat.
‘Vortex’ het flesje/flacon gedurende 10 seconden bij length in a slim bottle/flask.
Add boiling water until so that the entire stem is submerged.
Vortex the bottle/flask for 10 seconds at 2500 RPM.[2] Aanvullend nog 5x stevig verticaal schudden.
Bepaal de mate waarin de bastvezels los komen van de kern.
...
Additionally, shake firmly vertically for further 5 times.
Determine the extent to which the bast fibres detach from the core.
...
[1] http://www.global-sci.org/v1/jfbi/Biological-Treatment-of-Raw-Flax-with-Fungus
...